AMS Performance R35 GT-R Induction Kit

Carbon fiber intakes and 3″ upper piping in one complete GT-R system, proven beyond 1,800 HP.

$2,349.95

-

SKU ALP.07.09.0003- Categories , Brand:

California Residents: Prop 65 Warning

Additional information

Weight 12 lbs
Dimensions 21 × 12 × 12 in
Installed Intercooler

Stock, Alpha

Installed Intake Manifold

Stock, Alpha

Installed Throttle Bodies

Stock, Alpha

CARB And / Or EPA Compliance Testing Not Completed

While we believe this product is either CARB EO exemption applicable, or complies with the EPA's Anti-Tampering Policy, we have not completed the required testing and administrative process at this time. This product is not available to purchase for emissions-controlled vehicles located within the state of California, or available to ship to California addresses, without a completed AMS Race Waiver form. International users outside of the United States should act in accordance with their local laws and regulations.

Application(s):
2009-2011 (CBA) Nissan R35 GT-R | 2012-2016 (DBA) Nissan R35 GT-R | 2017-2019 (Facelift DBA / “EBA”) Nissan R35 GT-R | 2020-2025 (4BA) Nissan R35 GT-R
FREE SHIPPING on all orders over $199.99 in the lower 48. (Exclusions Apply)

With 25 years of documented research and development in the forced induction field, AMS Performance has proven itself as the powerhouse in the automotive aftermarket. Our award winning performance systems are what all others are measured by.

Proven on GT-R builds over 1,800 HP, the AMS Performance R35 GT-R Induction Kit pairs our Alpha carbon fiber cold air intakes with 3″ (76mm) upper intercooler piping that makes a speed density conversion possible without a rewire kit. Moving past the factory pull-through MAF setup delivers accurate fueling and smoother part-throttle drivability at power levels the stock system can’t handle. The TiAL-flanged upper pipes also let your blow off valves vent to atmosphere without upsetting the calibration.

  • Proven on builds over 1,800 HP
  • Speed density ready with no IAT rewire kit required
  • Smoother part-throttle drivability
  • 3″ (76mm) upper intercooler piping with roughly 60% more area than OEM
  • Hand-laid motorsports grade carbon fiber intakes rated to 240°C
  • Upper pipes flanged for TiAL blow off valves

 

Built for Speed Density

On the factory pull-through setup, the MAF sensors sit ahead of the turbos. At high power levels, airflow outruns the sensors, and any air vented by an atmospheric blow off valve has already been metered, which leads to rich stumbles on throttle lift. The GT-R Induction Kit is designed around a speed density conversion, the go-to route for big-power R35s today, which calculates airflow from manifold pressure and temperature instead of relying on the MAF. Simply mount the factory MAF sensors in the upper intercooler pipes, seal the intake pipe flanges with AMS R35 GT-R MAF Block Off Plates (sold separately), and your tuner uses only the temperature data from the MAF sensors. No rewire kit, and no reworking the MAF sensor harness to pick up an IAT feed. Prefer MAF-based tuning? The same setup runs the factory MAF sensors in a blow-through position.

3″ Upper Intercooler Piping

The kit replaces the 60mm factory upper intercooler pipes with full 76mm (3″) tubing, opening up roughly 60% more cross-sectional area between the intercooler and throttle bodies. Less boost is lost on the way to the engine, and every pipe is finished in durable wrinkle black powder coat. The upper pipes are flanged for TiAL blow off valves only, so plan your build around TiAL valves when ordering.

Motorsports Grade Carbon Fiber Intakes

Up front, our Alpha carbon fiber cold air intakes replace the bulky factory airboxes and draw cooler outside air into the turbos. Because the pipes sit close to the exhaust manifolds, they are hand laid from three layers of 1mm twill weave prepreg carbon fiber rated to 240°C, so they hold their structure and finish where cosmetic carbon would crack or cloud. With the factory airboxes gone, you’ll clearly hear the turbos spool and the blow off valves vent.

Alpha R35 GTR Carbon Fiber Cold Air Intake

 

Engineered to Match Your Build

The SnailWorks Engineering Team developed the GT-R Induction Kit in configurations for both stock and AMS intercoolers, intake manifolds, and throttle bodies, so the complete system bolts together the way it should. Most induction upgrades are designed to fit. AMS engineers them to dominate, delivering metering, airflow, and finish worthy of the most capable GT-R builds in the world.

 

Product Notes

  • A custom ECU calibration is required after installation. Failure to calibrate can cause engine damage.
  • Speed density conversions use AMS R35 GT-R MAF Block Off Plates, sold separately.
  • Upper intercooler pipes are flanged for TiAL blow off valves only.
  • Select your installed intercooler, intake manifold, and throttle bodies when ordering.
  • Installing with non-AMS aftermarket intercoolers may require additional parts and custom fabrication.
  • Because these carbon fiber intakes are hand laid from motorsports grade high-temp carbon, small imperfections and weave variations will be present, and no two are exactly alike.

Related Products

Search by product name, SKU or keyword